model g (mm) | Installation size (mm) | ||||||
A | B | C | D | h | H | d | |
150 | 920 | 110 | 210 | D273×5(4.5) | 260 | 396.5 | D159x4.5 |
200 | 1140 | 107 | 250 | D357x 6(4.5 | 328 | 506.5 | D219x6(4.5) |
250 | 1250 | 110 | 300 | D407x7(5.0) | 370 | 573.5 | D273×(5) |
300 | 1340 | 107 | 350 | D457×7(6.0) | 400 | 638.5 | D325x7(5) |
350 | 1430 | 119 | 360 | D507×B(6.0) | 435 | 688.5 | D377x8(6) |
400 | 1700 | 123 | 432 | D607x9(6.0) | 490 | 793.5 | D426x9(8) |
450 | 2000 | 140 | 480 | D709x 10(7.0) | 590 | 944.5 | D478x10(7) |
500 | 2200 | 140 | 530 | D813x12(8.0) | 650 | 1056.5 | D530×10(8) |
1. The remover is suitable for hot water system, with the working pressure of PN=4.0MPa and the nominal diameter of DN 150-500.
2, the data in parentheses in the table are suitable for PN=1.6MPa.
3. The sewage remover is installed on the brick breaker.
4. The decontamination is used to eliminate the dirt that falls into the hot water pipe during installation and operation, so as to protect the equipment and prevent the access blockage.
5. The sewage remover is installed on the water supply or backwater pipe at the heat exchange station or at the heat entrance of the hot water heating user.
6. The flange at the connection between the pipe and the fouator shall be prepared in JB / T81-94 according to the working pressure.
7. This drawing is drawn according to the national standard atlas of power facilities R406-2.
model g (mm) | Installation size (mm) | ||||||
A | B | C | D | h | H | d | |
150 | 920 | 110 | 210 | D273×5(4.5) | 260 | 396.5 | D159x4.5 |
200 | 1140 | 107 | 250 | D357x 6(4.5 | 328 | 506.5 | D219x6(4.5) |
250 | 1250 | 110 | 300 | D407x7(5.0) | 370 | 573.5 | D273×(5) |
300 | 1340 | 107 | 350 | D457×7(6.0) | 400 | 638.5 | D325x7(5) |
350 | 1430 | 119 | 360 | D507×B(6.0) | 435 | 688.5 | D377x8(6) |
400 | 1700 | 123 | 432 | D607x9(6.0) | 490 | 793.5 | D426x9(8) |
450 | 2000 | 140 | 480 | D709x 10(7.0) | 590 | 944.5 | D478x10(7) |
500 | 2200 | 140 | 530 | D813x12(8.0) | 650 | 1056.5 | D530×10(8) |
1. The remover is suitable for hot water system, with the working pressure of PN=4.0MPa and the nominal diameter of DN 150-500.
2, the data in parentheses in the table are suitable for PN=1.6MPa.
3. The sewage remover is installed on the brick breaker.
4. The decontamination is used to eliminate the dirt that falls into the hot water pipe during installation and operation, so as to protect the equipment and prevent the access blockage.
5. The sewage remover is installed on the water supply or backwater pipe at the heat exchange station or at the heat entrance of the hot water heating user.
6. The flange at the connection between the pipe and the fouator shall be prepared in JB / T81-94 according to the working pressure.
7. This drawing is drawn according to the national standard atlas of power facilities R406-2.
